All categories

Guangzhou a customer a poinsettia fill light

2017/2/9

1 Overview

2. System structure

2.1 fill light components

2.2 Distribution and control

2.3 List of raw materials

Construction and maintenance

3.1 stocking cycle

3.2 Construction cycle

4. Acceptance method

4.1 illumination

4.2 Control system

4.3 Power supply system

5. Use method and maintenance

6. Warranty

6.1 lamps and lanterns

6.2 Power supply and distribution system


1 Overview

The case should be used for poinsettia fill light, greenhouse specifications are as follows:

6 meters across a total of 10 spans, each span of 48 meters, spacing 3 meters a total of 16, the bed height of 0.5 meters, 3.5 meters high shoulder, insulation layer height of 2.5 meters

Design purpose: for the magenta light cycle control

Design illumination:> 50lx


2. System structure

2.1 fill light components

Fill light with 100W electronic ballast high pressure sodium lamp components, a total of 68 lights, the use of staggered distribution.

Lighting Model: SMART-100-E1-H, electronic high pressure sodium lamp, including electronic ballasts, lamp, MIDI reflector, 100 watts high efficiency high pressure sodium lamp light source.

Lamp installation effect shown in Figure 1:



                                                               Figure 1: SMAR-100-E1-H installation renderings


The use of high-efficiency plant light source for sodium light source, the spectrum shown in Figure 2:



Light distribution curve as shown in Figure 3:



                                                                  Figure 3: SMART-100-E1-H light distribution curve



Total power consumption: less than 107W


Total luminous quantity: greater than 10400 lumens


Total current: less than 0.56A@220V, the proposed 1 square millimeter of the national standard copper wire hanging less than 12 lights, 1.5 square meters of copper (or 2.5 square aluminum) hanging less than 17 lights.


Operating voltage: 175V ~ 264V, to ensure constant power constant illumination.


The whole light is bad: less than 2% @ 1000 hours


Ballast with power cord length: 60cm


Protection class: IP65, can be suitable for outdoor light rain conditions or humidity greater than 90% of the case, long-term stable work.


Installation: lifting, according to the actual situation to choose a fixed way


Wiring: power line, power zero line,


Light source: 10% of the light is expected to decline for 5 years, the damage rate of less than 10% (referring to the normal use of aging damage, not because the lamp installed substandard parts); light failure 15% for 8 years, damage rate of less than 15%.




Fill light with suspension installation, installed in the insulation layer, the installation of the highest degree of 2.5 meters., The effective height (light from the smooth surface to the surface of the bed) 1.9 meters lamp location shown in Figure 4.



                                                                          Figure 4: Lamp location map



2.2 Distribution and control


The system uses 220V two-phase power supply, need to provide 8KVA power supply capacity.


Supply voltage to allow fluctuations in the range, single to 176V ~ 264V.


The full power factor of the fill light is greater than 0.95.


Switchboard to install multiple air switches, contactors, time relay, to achieve regular control, manual control, support multiple overcurrent overheating protection; to avoid the impact of the power grid, fill light to achieve automatic delay group start control.


All components selected in line with the national standard industrial products.


2.3 List of raw materials


The case with 100-watt high pressure sodium lamp fill light components, a greenhouse use of fill light material list as follows:

Model Description Unit Price (RMB) Quantity (sets) Total price (RMB)
SMART-100-E1-H 100-watt high pressure sodium lamp kit
68

Construction and maintenance

3.1 stocking cycle

Raw material stocking includes lighting components, control components, cables and other procurement and acceptance, the expected time is 6 to 8 weeks.

3.2 Construction cycle

Construction includes the minimum unit installation and commissioning and the overall installation and commissioning, the estimated time is 4 days.


4. Acceptance method

4.1 illumination

Due to the height of the installation of the requirements of the illumination is low, can not meet the needs of illumination and uniformity at the same time, the case is the minimum number of lights in the case of simulation out of the illumination and even the best of a situation, of course, Can not achieve the ideal situation, please evaluate.

Through the software simulation, from the space arbitrary selection of random area, illumination as shown in Figure 5:



                                                                     

                    Figure 5: Point illumination chart


4.2 Control system

Basic functions: manual start, stop, automatic timer automatically stop.

Protection function: overcurrent protection, short circuit protection, overheating protection.

4.3 Power supply system

Material acceptance: cable, control components.

Installation of the normative: in accordance with national standard acceptance.


5. Use method and maintenance

My company to help users fill the light system responsible personnel to fully grasp the relevant technology, with independent capacity.

Our company offers one year free tracking maintenance, maintenance tools and materials provided by the user.


6. Warranty

Due to non-human misuse and non-natural force majeure and other causes caused by the light system components damage Our company provides the following warranty service, the starting time in accordance with the acceptance time to start the calculation.

6.1 lamps and lanterns

High pressure sodium lamp light source: 1 year free replacement. Its design life of 18,000 hours.

Reflector and lamp holder: 1 year free replacement. In the case of normal maintenance according to the "Use and Maintenance Manual", it is available for 10 years.

Electronic ballast: 1 year free maintenance. Design life of 20,000 hours.

6.2 Power supply and distribution system

Free consultation within 1 year.